"The Great Plan" stated that we would depart from NC and bring the boat down to the Virgin Islands. Frankly, we only went to Florida since we were short on time to make the passage... and because there are some interesting places to see down in the Bahamas, like Cay Sal Bank... and because I didn't really know how this boat would sail. But as we made our way to FL and found pretty significant leaks as well as weakness in the lower bobstay fitting, I lost some confidence in the boat... but regained it with good repairs.
Since then we've had the mainsail drop when the halyard wore through, then the replacement wore partly through twice, so I need to go up the mast AGAIN.... and (once the chafing is solved) will buy and install new line. We've found the water tank empty when the water line leaked, so I should run new water lines... and test them as I used to do when plumbing a home (although most homes never experience this sort of shaking!). We have run into a storm at night that left us only able to steer by compass and failed at doing so, finding ourselves running the engine and flopping in circles... with about ten termites landing on our faces as they flew to our headlamps!... (Solution: next time we will simply heave-to for the storm and let the natural stability lent by the sails and wind steady us. Not sure what to do about termites and have seen none since.). And the traveler for the main keeps locking itself into place for reasons too complex to detail, but that I solved yesterday. The jib sheets are too fat for the self-tailing winches (I looked up the specs yesterday and they are far outside spec). And I STILL have not replaced the fridge thermostat, turning it on and off with a switch instead.... although our main issue there is too little cooling rather than too much. And "improvements" by earlier owners have created issues. And the weather is so much more rough and unpredictable than we are used to having in the Virgins. And so much more... And poor Cynthia has to deal with THIS:
On the other hand, I just read this article to Cynthia (https://www.cruisingworld.com/good-times-and-smooth-sailing-while-crossing-atlantic) and it makes both of us far less hard on ourselves: it seems that a lot of stuff just happens. And we are really learning to become comfortable with the shallows, with the boat, and with the Bahamas weather: like a wild animal that has a very low survival rate when transplanted to a new location as they have not grown up there and learned all the details, we are finding learning all this new stuff to be uncomfortable, even painful, but are getting to the point where the joys outweigh the frustration, pain, and uncertainty. For example, Cynthia dove in a blue hole yesterday for the first time and really enjoyed it... and we have found some great reefs... and sunrises and sunsets always deserve attention.
So... we plan to continue sailing the Bahamas until we have ironed out the rough patches on our boat and our comfort level improves. Then we may sail south... or it may be time to sail north and away from hurricanes for the summer.
We shall see.
PS: does anyone want to come assist in sailing during the bits when Cynthia has to work? Drop me a line! We have room for at least five to sleep aboard...
Sunday, February 10, 2019
Thursday, January 31, 2019
First two weeks in The Bahamas
(Announcer): When last we left our intrepid voyagers, they were setting out for the Bahamas, promising to keep in touch via satellite phone technology and posting to sailblog! Now, back to the madmen!
Well.... I knew the satellite phone was finicky, so multiply that by two or three (the number of additional bits of electronica involved) and add in my serious lack of motivation while tired and damp and nervous and I should have predicted no posts. Sorry...I DO feel bad about it. If only I had an easy way of simply posting my location, something built-in to Iridium but lacking with Inmarsat.
The weather forecast looked weird, turbulent, highly variable depending on a few tens of miles change in location.. but OK... and I felt bad about keeping Cynthia in Florida longer. So we departed and headed south, hugging the coast, trying to get far enough south to cross the Gulf Stream without ending up in South Carolina. The wind (or lack thereof) didn't help.... we finally tried crossing and ended up twenty miles north of Abaco, a south wind that could have helped us cross twelve hours earlier becoming stronger and stronger and pushing us north. This sucked and grew rougher and rougher, but we did what we could and Cynthia even studied for her boards.... and then the main halyard snapped and the sail dropped....and the broken line fell into the water and fouled the propeller.
Well, wasn't THIS delightful! I really didn't want to sail into a strange harbor without a working engine, although I would have if I couldn't figure a safe way to handle it. We continued to sail for the Man-O-War entrance at Abaco Island sound and contemplated methods, then put the best into action.
Heaving-to during a brief lull in the wind (down to perhaps fifteen knots?) left the boat moving along at about a knot or so, slow enough that I could keep up by swimming if needed. With Cynthia as safety engineer and general assistant, a line in one hand, and a dive knife strapped to a leg, I snorkeled down, cut and unwrapped the line from the propeller shaft, and climbed back aboard. Easy!
We made our way to Marsh Harbor and called out on the radio for any marinas that could take a boat with our length and draft (everything in the Bahamas is SHALLOW) and a fellow responded and guided us in... to a shoal. And then onto another.. Enough: we dropped anchor and rowed over, checked in through Customs and Immigration, and headed back to the boat.
I could go on. Our outboard engine won't start and we need to put some effort into that. We replaced the main halyard and it chafed again (but we caught it in time. We smoothed the spot we guessed might be causing the chafing, but to no avail and will need to climb again and get more line. A leak developed again along the rudder post, so I tightened the compression nut. A couple fellows befriended us in Marsh Harbor and showed us the ropes, even helping get my spare phone set up for the Bahamas. We sailed south toward George Town in Great Exuma, but changed our minds part way and ducked in to Rock Sound Harbor in the south end of Eleuthra, enjoying the people there and hunting lionfish (Cynthia got eight) on the way out Wednesday noon. We sailed for Great Inagua, but stopped at Cat Island instead... and were visited by a couple out for a hour or so in a cat boat!
The weather is FINALLY getting warm as we travel south. And the stars are SO bright. And dolphins played around the bow as we approached Cat Island today and did acrobatics as we headed toward Eleuthra last week. And sunrises and sunsets delight.
And we both love cranberry pancakes for breakfast...
Tomorrow we should see what we can do about finding more lionfish, installing collars on the masts, fixing the fridge, solving the chafing halyard issue, etc, etc, etc.
Well.... I knew the satellite phone was finicky, so multiply that by two or three (the number of additional bits of electronica involved) and add in my serious lack of motivation while tired and damp and nervous and I should have predicted no posts. Sorry...I DO feel bad about it. If only I had an easy way of simply posting my location, something built-in to Iridium but lacking with Inmarsat.
The weather forecast looked weird, turbulent, highly variable depending on a few tens of miles change in location.. but OK... and I felt bad about keeping Cynthia in Florida longer. So we departed and headed south, hugging the coast, trying to get far enough south to cross the Gulf Stream without ending up in South Carolina. The wind (or lack thereof) didn't help.... we finally tried crossing and ended up twenty miles north of Abaco, a south wind that could have helped us cross twelve hours earlier becoming stronger and stronger and pushing us north. This sucked and grew rougher and rougher, but we did what we could and Cynthia even studied for her boards.... and then the main halyard snapped and the sail dropped....and the broken line fell into the water and fouled the propeller.
Well, wasn't THIS delightful! I really didn't want to sail into a strange harbor without a working engine, although I would have if I couldn't figure a safe way to handle it. We continued to sail for the Man-O-War entrance at Abaco Island sound and contemplated methods, then put the best into action.
Heaving-to during a brief lull in the wind (down to perhaps fifteen knots?) left the boat moving along at about a knot or so, slow enough that I could keep up by swimming if needed. With Cynthia as safety engineer and general assistant, a line in one hand, and a dive knife strapped to a leg, I snorkeled down, cut and unwrapped the line from the propeller shaft, and climbed back aboard. Easy!
We made our way to Marsh Harbor and called out on the radio for any marinas that could take a boat with our length and draft (everything in the Bahamas is SHALLOW) and a fellow responded and guided us in... to a shoal. And then onto another.. Enough: we dropped anchor and rowed over, checked in through Customs and Immigration, and headed back to the boat.
I could go on. Our outboard engine won't start and we need to put some effort into that. We replaced the main halyard and it chafed again (but we caught it in time. We smoothed the spot we guessed might be causing the chafing, but to no avail and will need to climb again and get more line. A leak developed again along the rudder post, so I tightened the compression nut. A couple fellows befriended us in Marsh Harbor and showed us the ropes, even helping get my spare phone set up for the Bahamas. We sailed south toward George Town in Great Exuma, but changed our minds part way and ducked in to Rock Sound Harbor in the south end of Eleuthra, enjoying the people there and hunting lionfish (Cynthia got eight) on the way out Wednesday noon. We sailed for Great Inagua, but stopped at Cat Island instead... and were visited by a couple out for a hour or so in a cat boat!
The weather is FINALLY getting warm as we travel south. And the stars are SO bright. And dolphins played around the bow as we approached Cat Island today and did acrobatics as we headed toward Eleuthra last week. And sunrises and sunsets delight.
And we both love cranberry pancakes for breakfast...
Tomorrow we should see what we can do about finding more lionfish, installing collars on the masts, fixing the fridge, solving the chafing halyard issue, etc, etc, etc.
Thursday, January 17, 2019
Out of Florida, heading ... south? east?
The new cable bobstay in place of the old chain looks great and ready for adventure.
I don't think the bilge pump has turned on more than a time or two since we repaired things, at least I've never caught it in action. The new alternator belt is finally tight enough.. I hope... that we will no longer open the engine room to find piles of rubber dust and a loose belt. Cynthia has packed every space in the boat with goodies and I have no idea where most things are, but I'll find them. Yesterday she even made a fitted sheet for our bed in the aft stateroom. And we've done so many more things! I think we are ready, finally, to depart....even though the dinghy leaks abominably (I'll fix it as we sail).
And, of course, when one is ready, the weather has to butt-in with issues.... it looks QUITE interesting, enough so that I even considered odd options. I think we will simply head south, spend a day on Cay Sal Bank, then continue southeast toward the Virgin Islands. Possibly we may stop in the Bahamas or Turks and Caicos, or we may push on through. We shall see.
I've found a good blog site and an email service that will work over my satellite phone, but it is all plain text: even signing into gmail would take hours at the slow data rate available. So, if you want to follow us, go to https://www.sailblogs.com/member/hydrophilia/
or contact us at hydrophilia@satxgate.com
I'll post our location and a few words at least once per day, probably twice. We may go fast and get to St John in ten days, but more likely will mess about and get there in a matter of three or four weeks.
Adventure!
I don't think the bilge pump has turned on more than a time or two since we repaired things, at least I've never caught it in action. The new alternator belt is finally tight enough.. I hope... that we will no longer open the engine room to find piles of rubber dust and a loose belt. Cynthia has packed every space in the boat with goodies and I have no idea where most things are, but I'll find them. Yesterday she even made a fitted sheet for our bed in the aft stateroom. And we've done so many more things! I think we are ready, finally, to depart....even though the dinghy leaks abominably (I'll fix it as we sail).
And, of course, when one is ready, the weather has to butt-in with issues.... it looks QUITE interesting, enough so that I even considered odd options. I think we will simply head south, spend a day on Cay Sal Bank, then continue southeast toward the Virgin Islands. Possibly we may stop in the Bahamas or Turks and Caicos, or we may push on through. We shall see.
I've found a good blog site and an email service that will work over my satellite phone, but it is all plain text: even signing into gmail would take hours at the slow data rate available. So, if you want to follow us, go to https://www.sailblogs.com/member/hydrophilia/
or contact us at hydrophilia@satxgate.com
I'll post our location and a few words at least once per day, probably twice. We may go fast and get to St John in ten days, but more likely will mess about and get there in a matter of three or four weeks.
Adventure!
Friday, January 4, 2019
Sonoma visit December 2018
How fast the decades pass! Nearly three of them have gone by since I gutted the house my folks bought and rebuilt it for them. And they have mostly been quite happy with it. Of course, there are things that need work from time to time. Last time I was here I replaced a few deck planks, this time I'm working in the attic (nice and cool this time of year), crawling under the house, pruning, etc.
Progress remains slow: although I've recovered considerably in the years since I quit my carpentry here, I still find that working in the attic (or under the house or weeding or on the deck) leaves me hurting rather quickly... and, day by day, I was finding myself stiffer and groaning more loudly: time wounds all heels (not to mention backs and knees). After over ten days, however, I think I've found an amount of work that, combined with yoga and walking each day, leaves me no worse off than the day before.
And solving problems and fixing things brings satisfaction. Doing a good job brings satisfaction. And I get to visit my folks and extended family. And Chris (an old friend) and I checked out Jack London museum and walked around the remains of his amazing house.
And, yes, I am eager to get back aboard the boat and point her nose toward adventure.
Progress remains slow: although I've recovered considerably in the years since I quit my carpentry here, I still find that working in the attic (or under the house or weeding or on the deck) leaves me hurting rather quickly... and, day by day, I was finding myself stiffer and groaning more loudly: time wounds all heels (not to mention backs and knees). After over ten days, however, I think I've found an amount of work that, combined with yoga and walking each day, leaves me no worse off than the day before.
And solving problems and fixing things brings satisfaction. Doing a good job brings satisfaction. And I get to visit my folks and extended family. And Chris (an old friend) and I checked out Jack London museum and walked around the remains of his amazing house.
And, yes, I am eager to get back aboard the boat and point her nose toward adventure.
Sunday, December 9, 2018
replacing the bobstay
Firstly, the bobstay is the chain or cable that leads down from the tip of the bowsprit to near the waterline of the boat and counteracts the upward forces from the forestay. These forces can be HUGE.
Almost every time I approached my boat in Wayfarerer's Cove, my eye fell on the lower bobstay fitting and I would often wonder if it was sound...but the fellow I had survey my rigging did not say anything about it, so I tried to ignore it. Also, I HAD looked at both exterior and interior of the fitting and saw no issues....although someone had completely hidden the interior with a plaster of fiberglass.
Three or four days into our passage from NC to FL, while puttering and inspecting (I've heard lots of tales of major problems that sneak up on people.... and previously DID find the bilges nearly full on a different boat (not one of mine) due to a leak and a shut-off bilge pump and have heard of losing engines and of near-abandonments caused by same) I found some issues with the bilges. The main concern was the bilge pump running frequently, so I cleaned the bilges, cleaned the pump, and made sure everything worked well....but fretted over the constant trickle of water.
I tracked the trickle through the bilges, opening various hatches in the sole (floor) until I reached the bow, dug down through storage and anchor chains to get to see hidden things....and found a rather rapid trickle (maybe a cup every five minutes....maybe faster) coming from the lower bobstay fitting....well, from under that mass of glass someone had packed in there. I pumped out the little pond there, groped around, and found rotten wood and mud and water in a void I could feel but not see. I guess that plunging through waves had washed away enough mud to let water flow more freely than in the marina.
Among the many things I applaud Cynthia for, staying calm and analytical under threats ranks high. She simply asked about my strategy for the leak and I told her plan A, B, and C (I LIKE backup plans!) and she seemed fine. We packed bedding foam ripped from a mattress into the hole as tightly as possible, then installed a scrap of wood as a brace to keep everything as tight as possible. This reduced the leak by perhaps half and we planned to live with this (and frequent bilgewater inspections) until we reached Vero Beach, our planned destination.... but were prepared to change our plans as needed.
I also tracked another trickle to the stern of the boat..... and found it coming in from a loose packing nut around the rudder post. I guess the boat had sat long enough that being active opened up a leak, but a minute tightening it with the channel lock wrench dropped the flow to nothing.
SO! Once in Vero Beach City Marina we shifted everything heavy to the stern of the boat, lifting the bobstay fitting and stopping the leak. I intended to clean the fitting, replace the bolts, and install new backing.First step: chip off the fiberglass sticking plaster and remove the nuts, bolts, backing plate, fitting, and the rotten wood that had acted as reinforcement since the boat was built.
The corrosion had left the stainless backing plate looking like lace, so that went into the trash.
I dropped the bolts into my green phosphoric acid to clean them and, with the rust gone, they looked as though rats had been chewing them, so... into the trash! The bobstay fitting, cleaned and treated with acid looked nice and clean...
but heavily pitted and not to be trusted. OK....now I had to find one for sale or get one made at the local machine shop. Nothing could be salvaged from the assembly.
I dropped the bolts into my green phosphoric acid to clean them and, with the rust gone, they looked as though rats had been chewing them, so... into the trash! The bobstay fitting, cleaned and treated with acid looked nice and clean...
but heavily pitted and not to be trusted. OK....now I had to find one for sale or get one made at the local machine shop. Nothing could be salvaged from the assembly.
A search online found a place in Maine, Spartan, that specializes in bronze castings and the strength of their larger bobstay fitting, 25,000lbs, fits my boat reasonably (perhaps I'l do the math in another post). I ordered it and got to work on replacing the rotten wood reinforcement... with a far stronger and harder thickness of epoxy-reinforced fiberglass.
Methodology? Wire brush and clean and dry the region to be repaired. Soak a bunch of triaxial glass cloth with resin, roll it into a nice tight roll, place it where the wood was, place waxed paper over it, then a piece of wood, and brace the whole assembly to squash it into a flat-topped low-resin, high-glass hunk about 1.5" thick. This will NEVER decay.
Once the fitting arrived I drilled holes through the glass (NOT easy: that stuff is VERY hard) and bolted the fitting loosely into place through a nice bed of UV-resistant caulking, gave it a couple days for the caulk to cure, then tightened bolts,
reinstalled the bobstay, reconnected the forestay and jib, and tightened and adjusted all the other stays.
reinstalled the bobstay, reconnected the forestay and jib, and tightened and adjusted all the other stays.
Of course, life often gives us little extras to deal with: while installing the bobstay I dropped the rod that braces the middle ("dolphin striker") and it disappeared into the murky water with a mocking "plop!". I dove for it, but found darkness and soft mud, so quit looking and dropped a marker for tomorrow, then went off to rest until my ear equalized and I stopped losing lunch....repeatedly. Happily, I got connected to a diver who took under five minutes the next morning to find the little mark in the mud where the rod was buried and recover it, so now all is well.
And the boat can sail again!
Tuesday, December 4, 2018
Bending chainplates
One thing keeps leading to another. In this case, I noticed that quite a few clevis pins (the large pins on the stays) were too long. This allows other bits of metal to shift and spread and makes things weak. So.... I purchased a bunch of new pins from my favorite source (about $5 each instead of the local price of around $20 to $25 each) and went around loosening the stays, replacing the incorrect pins with the right ones, and tightening things back up... and then I came to the foremost starboard stay.
Well, I managed to pull the old pin, but installing the new one just wasn't in the cards: even though the pin fit every hole, it would not fit through all of them. It turned out that this was caused by misalignment of the holes due to the strap being deformed due to uneven forces due to the chainplate not being aligned with the stay!
So.... what to do? Pull the chainplates off the boat and take them to a person who could bend them? Get a BIG crescent wrench and bend them? Make up something out of steel, perhaps a piece of square tubing with a slot in the end? After chatting with my friend David about possibilities, I pulled out some bolts and hardwood I had aboard and made up a tool, although I was not optimistic.
I bolted it onto the starboard chainplate and gave a light tug.... and the steel bent easily.
WELL! I bent it a bit more to align with the stay, unbolted it, and installed the stay with the new, shorter clevis pin. BEAUTIFUL!
OK, the matching port stay was also wrong, so I bent it, too. And the pin refused to go in. I checked and it seemed that it was drilled just a few hundredths of an inch smaller than required for a 1/2" pin: perhaps they had used a 12mm pin? Anyway, I borrowed a 1/2" bit from David and all is now installed, aligned, and repaired.
Most satisfactory.
Next time: bobstay fitting?
Sail cover?
Or maybe the refrigerator. Or perhaps the aft hatch.
NEVER a shortage of subjects to repair!
Well, I managed to pull the old pin, but installing the new one just wasn't in the cards: even though the pin fit every hole, it would not fit through all of them. It turned out that this was caused by misalignment of the holes due to the strap being deformed due to uneven forces due to the chainplate not being aligned with the stay!
So.... what to do? Pull the chainplates off the boat and take them to a person who could bend them? Get a BIG crescent wrench and bend them? Make up something out of steel, perhaps a piece of square tubing with a slot in the end? After chatting with my friend David about possibilities, I pulled out some bolts and hardwood I had aboard and made up a tool, although I was not optimistic.
I bolted it onto the starboard chainplate and gave a light tug.... and the steel bent easily.
WELL! I bent it a bit more to align with the stay, unbolted it, and installed the stay with the new, shorter clevis pin. BEAUTIFUL!
OK, the matching port stay was also wrong, so I bent it, too. And the pin refused to go in. I checked and it seemed that it was drilled just a few hundredths of an inch smaller than required for a 1/2" pin: perhaps they had used a 12mm pin? Anyway, I borrowed a 1/2" bit from David and all is now installed, aligned, and repaired.
Most satisfactory.
Next time: bobstay fitting?
Sail cover?
Or maybe the refrigerator. Or perhaps the aft hatch.
NEVER a shortage of subjects to repair!
Saturday, November 24, 2018
We made it to Florida on speaking terms and without sinking!
Busy, busy, busy!
I dropped Cynthia off at the Melbourne airport this morning and miss her terribly. Our shakedown cruise was quite successful on just about all counts:
Getting good advice and tools from friends? Check! (Thanks, Nate! WaterwayGuide.com is GREAT!)
Getting out of marina? Check! (Although we had to wait nearly a week to be ready and to have the right conditions.... and had to pull out in rain and wind and cold. We were SO grateful to have an enclosed cockpit!)
Sailing to ICW (Intracoastal Waterway... some say Intercoastal) and anchoring for the night? Check. (We had some nasty weather when sailing out and really harsh winds during the night, but the anchor held and, even with the wind removing 2' of water in the night, still has a few inches of water under our keel in the morning)
Sailing and motoring down the ICW? Check.
Stop in at an unfamiliar marina and get advice, fuel, and a replacement inverter? Check.
Continue south and into the open ocean before sunset? YES!
Sail and motor south in the open ocean, 30 to 50 miles from shore for five days? Yep... and saw wonderful porpoises, phosphorescence, shooting stars, sunrises, and sunsets.
Handle minor and major issues well? Yes, we did. The rather major rivulets of salt water running into the bilges were tracked down and handled pro tem, with further repairs to be done in the next week. The inverter I turned into a smoking piece of garbage was replaced. Before departing on our voyage, Cynthia talked me into pulling the handrails from the top of the cabin, stripping and refinishing them, and bolting them down in a really nice bed of good caulking that should stop those leaks for a decade....I hope.
Dawdle offshore in FL overnight while waiting for morning light to make harbor entry safe? Yes, although listening to the coast guard warnings about small craft warnings and notices about an overturned catamaran made it a long night.
Enter the ICW at Fort Pierce and ride the current up the ICW to Vero Beach? Call the bridge operator to raise a drawbridge for us? Did that! Even ate tasty omelette Cynthia cooked as we motored along.
Note: there are two entrances we can use to get to Vero Beach and next time we will use the one that allows us to SAIL most of the way on the ICW: so much nicer than motoring!
Note: there are two entrances we can use to get to Vero Beach and next time we will use the one that allows us to SAIL most of the way on the ICW: so much nicer than motoring!
We did NOT catch any fish on hook and line. Our only catch was accidental: we found this stiff flying fish on deck one morning.
And we have already made new friends in the marina (Vero Beach City Marina) and seen my friends Georgia and David from St John (the reason we came here) and met lots of their delightful friends who live around here. Great folks!
Current plan is to keep the boat here, rafted up with Bob and Robin's boat (the marina tells you you WILL raft up if they have limited space), until January.
I'll stay aboard for a few weeks and make repairs and do some sailing, then visit Cynthia in MI, then take the boat south-east to the Virgin Islands, meeting Cynthia there about January 22. (Yes, I could use company sailing the boat down, but CAN do it alone.). My mom will probably visit for a week and go watch the Geminid meteor shower on a night sail.... and be the second family member to see this boat.
And last night a crane landed on our mooring buoy...
Subscribe to:
Posts (Atom)










































